When installing NTV Plus equipment yourself, first of all it is necessary to carry out high-quality installation and installation of technical equipment.

1. It is worth taking into account that the satellite television operator NTV Plus has several different manufacturers dishes, and the exact direction angle of the television dish itself (from 17 to 38 degrees) will depend on them.

The dish also needs to be pointed south since the NTV satellites themselves are located high above the equator. For accuracy, it is recommended to use a compass.

2. In order for the image quality to be excellent, it is necessary to install the antenna in such a way that the receipt of the television signal is not obstructed by various high-rise buildings, trees, structures, etc.

3. The installation of the bracket must be approached with maximum responsibility. The quality of the signal will depend on the strength of the installation.

Otherwise, over time, the plate may turn around or settle, the direction angle will change, which will certainly affect the level of the television signal.

4. The cable must be durable and resistant to weather conditions.

Important! Be sure to consult with the NTV Plus operator before installing technical components yourself.

After installing the equipment, you need to configure the antenna itself (satellite dish):

• First the conversion cable must be connected to the receiver. The device receiving the signal is connected to the television device;

Note! For proper operation of the equipment, in order to avoid its breakdown or poor quality work, carefully read the installation and operating instructions!

• a small mirror installed on the dish must be carefully rotated (right/left/up/down), thereby adjusting its exact direction towards the satellite.
• In this case, you need to observe the changes on the TV screen. Manipulations must be done before the image appears;

• When the presence of an image has been detected, the “Signal reception level” function must be activated on the receiving equipment. The higher the value on the signal definition scale, the better the image will be.

Equipment registration

To make further settings, you should register on the official resource of the NTV Plus operator.

This must be done in order to register the access card and CL module.

Module CL- this is a device that, using a special hole in the TV and a decoding device (access card), allows the subscriber to gain access to closed programs of the television operator.

After registering and activating it through email V personal account the user will be able to activate such a service as “Contract Registration”.

After registration, the access card will be activated automatically within 24 hours.

Receiver setup

If you use your own equipment and an NTV Plus dish, then when using standard settings receiver recommended for users of NTV satellite television, the receiver will be configured to the required parameters automatically.

To do this, just use the remote control to turn it off and then turn it on again.

If automatic setup does not occur, try disconnecting the terminal from the source electrical supply, and upon further connection to the network, repeat the manipulations.

If, after the above recommendations, automatic tuning does not occur, you should reset all settings to the factory settings, after which the receiver will begin again to automatically search for channel settings of the NTV plus television operator.

Don't forget to check the level of the signal reception scale, the problem may be a low frequency.

Setting up NTV plus channels

In this case, channel tuning can occur either automatically or through manual settings.

To implement automatic setup channels, you should select “ Automatic installation channels."

If you have installed the equipment correctly, all channels will be tuned in fully automatically without your participation within a few minutes.

Searching for channels manually is a more labor-intensive process:

1. You need to reset the settings to factory defaults, then in the Menu item you need to select Settings, and then Default Installation.

After selecting this item, select Channels, Antenna, and then Satellite Settings.

2. The receiving equipment will ask for a password, which, when set to factory settings, corresponds to four zeros (“0000”).

If you managed to change this numeric value, then enter your option.

3. In the window that appears, you will see a list of allowed satellites.

It is necessary to remove the checkmarks next to each of them, leaving only Eutelsat w4 36e. If the function is unavailable for some reason, you must remove the access card from the device.

4. Afterwards, you need to configure the receiving device (transponder) itself according to the following parameters: 12130 “R”, the lower level of the LNB should correspond to “0”, and the upper level to “10750”.

5. So, after changing all the above settings in manual mode settings, you must select the one recommended by the device receiving equipment and set a goal

Search the web. Possibly in this mode Setting up the channels will take quite a lot of time, but all the channels included in the package will certainly be configured as expected.

Setting up Samsung and LG TV

TV models from these companies often automatically have a CAM module.

CAM module, or conditional access module, is a decoding device built into the TV that allows you to receive television signals closed access.

Samsung TV setup instructions:

1. Using the remote control, you need to go to the Settings Menu of the TV itself, and select “Broadcast” there.

3. Next, go to the LNB Settings section (the LNB converter receives satellite signals and converts them into low-frequency ones), and select any receiving device recommended by the device. You need to turn off DiSEqC mode, and the tone is 22 KHz. The lower level of the LNB should correspond to “9750”, and the upper level to “10750”.

6. From the list of satellite antennas, again select Eutelsat w4 36e, and from the list of transponders, select the one listed under number 11900 (v/r) 27500, and then agree to save the settings.

7. Select “Search network”.

9. In the “Sorting” Menu item, you can assign channels to various target categories, for example, News Channels, Children's Channels, Entertainment, etc.
After this, the Samsung TV setup is considered certified.

LG TV setup instructions:

1. Using the remote control, you need to go to the TV settings and select the “Broadcast” item there.

2. A list of satellite antennas will appear again, from which you must select Eutelsat w4 36e. After this, it is better to save the settings.

3. Next, go to the LNB Settings section and select any receiving device recommended by the device. You need to turn off DiSEqC mode, and the tone is 22 KHz. The lower level of the LNB should correspond to “9750”, and the upper level to “10750”.

4. On the control panel, press the “Return” button twice.

6. From the list of satellite antennas, again select Eutelsat w4 36e, and from the list of transponders, select the one listed under number 12322 (r) 27500, and then agree to save the settings.

7. Select “Search network”.

8. In the Menu we again find the Broadcast section, and in it Change Channels. If you need to assign a specific number to a channel, we do this using the “Change number” function

9. In the “Sorting” Menu item, we can also divide channels by topic.

It’s great if your TV works well and on long evenings you have something to do by watching your favorite TV shows. But it happens that television works intermittently. In order not to feel discomfort, you can buy an NTV dish, and use the receiver to set up a satellite dish, and ultimately enjoy your favorite programs at any time of the day or night.

Installation and configuration of the NTV antenna is available to every user who can try to do it themselves. But still, it is better to trust the professionals to enter some parameters if you are not sure that you can carry out all the procedures on your own. There can be no question about choosing the right satellite television provider; NTV is one of the leaders in the Russian market, which is why NTV dishes are so wildly popular.

How to install a satellite dish

First of all, you need to make sure that all the necessary components and equipment are available, because anyone who has installed a satellite dish knows that sometimes the equipment is incomplete, or a person simply does not understand why this or that thing is needed. So, let's look at what you need for installation:

You can’t do without a satellite receiver or built-in set-top box;

udCoaxial cables with connectors;

A plate with a diameter of at least 60 cm;

Access card and converter;

Instructions and agreement.

In addition, setting up NTV Plus begins with registration on the company's official website, where the user must register his equipment, otherwise it will not work.

In order for the satellite to receive the signal, a place where there is no interference is chosen for installation. There should be no tall trees, buildings or other obstacles that would prevent the equipment from operating as intended.

The most suitable place to set up satellite dish went well, is the roof. If it is not possible to install a satellite, you can use an external wall, but again, make sure that nothing interferes with the signal.

It is very important to protect the device from bad weather conditions, which are not uncommon in Russia. When the location is chosen, among the equipment you need to select a bracket that will fix the antenna. We connect the cable and stretch it to the TV. Places where you need to attach the cable to Sony TVs and Samsung are different, and if the receiver is not built-in, then the wire will have to be connected to it.

Self-tuning NTV Plus

After the antenna is installed and all the necessary cables are connected, you can proceed to the most important step - finding out the settings for the satellite. For example, be sure to find out what frequency the signal is. If after entering the information the channel does not show, it means that something was done wrong. Need to find alternative way how to set up channels on an LG TV, or on any other device, in particular on Samsung or Sony models.

On this moment, you can use two ways to configure channels:

1. Automatic.

The second requires virtually no effort on the part of the user, as it can be done by pressing a few keys on the remote control. In particular, you need to enter the menu, and then select the “Search for channels” sub-item. If the parameters on the receiver were correctly set, including the frequency, then the setup will end successfully.

In addition, you can buy the Cardsharing NTV Plus package where the settings have already been made, and the user only has to connect it. But the receiver must connect to sharing in order to connect even more interesting channels.

Manually setting up a satellite dish

As for manual search, it is much more complex, and it is not recommended to conduct it without experience. However, here's how it works:

First you need to reset all existing settings, if they have been installed. It looks like this: menu, “SETUP” → “DEFAULT INSTALLATION” → “CHANNELS” → “ANTENNA” → “SATELLITE SETUP”;

Next, use the receiver to set up a satellite dish, and when the program asks you to enter a password, you must enter a number consisting of four zeros;

A tab will open in front of the user, where there will be many satellites. Some have check marks next to them. These are allowed by default. You need to remove the marks opposite the satellite, otherwise their broadcast frequency will also be taken into account. But be sure to leave EutelsatW4 36E. Sometimes such a procedure may be blocked for the user. To open access, you can remove the access card;

Check the transponder, or rather its parameters. Typically, the following indicators are used: 12130 R and Lnb levels (lower = 0; upper = 10750);

After the transponder is configured, it’s time to move on to the final stage, namely entering all the parameters into a special line. Find out what the broadcast frequency is and enter it in the “MANUAL SETUP” section. Select the previously specified transponder to begin searching the network.

Be prepared that the search will take a long time, but the tuned antenna will show any channel you want.

How to set up an NTV Plus Vostok antenna on different TVs

Depending on what kind of TV you have, the settings are slightly different. It's very easy to understand. In particular, Samsung and LV TV models are configured as follows:

Make sure that the devices have a CAM module;

Go to the menu and select “BROADCAST”;

Go to selected antennas, check the box next to EutelsatW4 36E;

Save the specified settings.

Find in the “LNB SETTINGS” tab and select the transponder. Which one doesn't play a big role.

Make sure DiSEqC mode is turned off. Specify the following settings: Lower LNB = 9750. Upper LNB = 10750. Be sure to turn off the 22 KHz Tone.

On the remote control, press the “Return” button twice and go to manual channel search.

Select the satellite EutelsatW4 36E, transponder with the number 11900(V/R) 27500 and set the search.

If you set it up professionally, you can sort the channels into categories to make them easier to use. As for setting up satellite television on an LG TV, it follows the same scheme, only other parameters are taken into account. They can be found in the instructions.

Instructions

Install the satellite dish in a place where there will be no objects blocking it. These include tall trees with spreading crowns and nearby buildings. Since the NTV+ satellite or Eutelsat W4 is located strictly in the south, its entire location is in the direction of the sun. At 13.00 Moscow time it is located exactly in this direction. In addition, you should know the location angle or tilt angle of the antenna. For example, in the southern part of Russia it will be directed upward by about 45 degrees, in Moscow it will stand almost vertically, in St. Petersburg it will look “at the ground.” This is due to the curvature of the offset mirror.

Install a converter with circular polarization on the satellite dish, preferably with the plug facing down to prevent moisture from entering. Connect the coaxial cable from the converter to, and from it to. Turn on the tuner. Find the receiver channel on your TV. Using the buttons on the tuner remote control, configure the NTV+ info channel in the menu according to the parameters 11900 R 27500. When the channel window is set to 0% signal quality and 0% power, start turning the antenna left and right. After passing the sector, raise or lower the plate one degree and scan the horizon again. If there is no NTV+ satellite in the tuner settings, set the Eutelsat W4 satellite in the menu (local oscillator frequency 10750), turn on the converter power, DiSEqC input, turn it off and try again to find channels on the NTV+ transponder.

Fix the antenna after a stable signal appears. It will be visible by the change percentage values signal strength and power in the channel window. In the same way, configure the satellite dish to the FTA (open) NTV channel on the ABS 1 75e satellite. It is located on the 12640V22000 transponder. This requires a Ku-band linear converter; these technical data are written on its body. The ABS 1 75e satellite is located on the left side of the Eutelsat W4 satellite.

Sources:

• NTV satellite settings

How could people get by without a plate before? There is now a TV in every home, and people boast of a wide selection of channels. Even if it’s impossible to watch all 64 channels at the same time, the main thing is that he has this same dish. Every avid TV viewer can connect a dish at home.

You will need

• Tool kit, dish, cable, DVB card, receiver.

Instructions

Connect the dish converter to the DVB card using a cable, and first install the connectors on it.

Pay attention to the receiver when you rotate the antenna to search for a signal.

Now that the signal is becoming clearer, choose the final location of the antenna and secure it with bolts and nuts.

note

Try to secure the plate tightly so that it does not move during gusts of wind or severe frosts.

Helpful advice

You can configure the dish using the data shown not by the receiver, but by the DVB card tuner program.

Sources:

• Detailed description steps to connect the dish.

Satellite television And Satellite Internet are not something exotic in our time. Any place where there is satellite coverage, you can watch TV channels V digital quality. In addition, if you have a computer and a DVB card, then by tuning in to your Internet provider, you can always connect to the network via an asynchronous or two-way channel. However, the main thing is to correctly configure the satellite dish to receive the signal. There are several options for doing this, one of them is using a compass.

Instructions

Install the satellite dish in a place where it is not covered by high-rise buildings or tall trees, otherwise the TV picture will “scatter” or there will be no way to catch a signal from the satellite transponder at all. The bracket and the pole on which it will be fixed must be fixed strictly horizontally or vertically, respectively.

Determine the geographic coordinates of your location. For this purpose on the website www.maps.google.com in the search bar, enter your city, coordinates (eastern longitude, east, and northern latitude, north). A red marker will appear on the map, right-click on it and select the “What’s here?” tab. The coordinates will appear in the “Search” line. For example, Donetsk (Ukraine) has geographical coordinates: 48.028968 E, 37.802582 N.

Use the site www.dishpointer.com, where also enter the name of the city or its coordinates. In the drop-down menu below, select the satellite to which you decide to tune the antenna. After that on satellite map select your location in the city and click on it. The green beam will indicate the direction of rotation of the antenna, and at the bottom of the map the values ​​in degrees will be shown: elevation (tilt angle of the dish mirror), azimuth (true) (compass azimuth), LNB Skew (converter rotation). For example: Donetsk (Ukraine) – satellite setting ABS 1 75e, elevation: 24.3 degrees, azimuth (true): 134.4 degrees, LNB skew: -28.5° (“minus” means turning right counterclockwise relative to vector perpendicular to the ground).

Take a compass and rotate the satellite dish according to this data. Place the mirror vertically. Loosen the fastenings slightly and start scanning the sector, moving the antenna left and right. When a signal appears, achieve its maximum value and record it. Adjust the signal strength with the converter and secure it. If no signal is detected, lower or raise the antenna one degree after each pass.

Sources:

• how to set up a satellite dish using a compass

Satellite television means you can watch hundreds of channels in many languages. To gain access to global digital television broadcasting, you need to purchase the necessary equipment and configure it correctly.

Instructions

You will need an antenna that receives the signal from the satellite, a receiver, an antenna mount, converters, a switch and a cable. Find out which satellites your home is within range of. The website www.lyngsat.com will help you with this. There you can also get precise information about which channels are dependent on each satellite.

Place the antenna on the south side of the house and make sure it is not obstructed. Decide on its direction. The most basic way is to look at your neighbors' antennas. If you have nothing to compare with, the direction can be determined by azimuth using special program Satellite Antenna Alignment. Once you know the direction, securely install the antenna on the mount.

Connect the receiver and TV and start setting up. In this case, it is better to make sure that the receiver is close to the antenna, then you can immediately see the results of your work. Connect the converter to the receiver and display the signal strength indicator from the satellite on the TV screen. Then slightly loosen the mount on the antenna and begin to carefully turn the antenna left and right, monitoring the signal level. After determining the best position for the antenna, secure it completely. Be very careful, as moving the antenna just a couple of millimeters can result in the search having to start all over again.

Adjust the position of the converters. Typically, the central converter receives the signal from the closest satellite, and the side converters receive the signal from the others. Once setup is complete, attach the DiSEqC switch and route the cable.

Tune channels on your TV. You can run auto mode, then you will have hundreds at your disposal satellite channels from all over the world, or you can, using manual settings, select only a few that you really want to watch. That's it for installation satellite equipment finished. Enjoy watching.

Video on the topic

A satellite dish opens up a whole range of possibilities. Installing it yourself is relatively easy. The main thing is to stock up on the necessary tools and patience.

Instructions

Decide on the location where you want to place the satellite dish. A number of difficulties arise here. Firstly, there should be no large obstacles in the path of contact between the antenna and the satellite: a tree, a tall building, a massive metal structure, etc. All these objects can significantly degrade signal reception, which will further complicate the setup of many channels.

Take a hammer drill. You can’t do without it if you want to install a satellite dish in a concrete floor, wall, roof, balcony railing, etc. Make holes of a diameter sufficient to allow medium-sized bolts to be screwed into them, since the weight of the entire structure requires massive fasteners.

After the holes are ready in accordance with the markings on the antenna mounting surface, take the anchor bolts. They will allow you to achieve sufficient rigidity in fastening a structure of such weight. Screw them in. Attach the antenna stand to the anchor bolts.

According to the assembly diagram, assemble the remaining part of the structure to install the satellite dish. Provide rigid mounting and the ability to rotate the dish itself to adjust the angle of inclination to achieve maximum signal clarity.

Drill another hole. This time through. Through it you will run the cable from the satellite dish to the receiver. When the cable is connected, select the “Channel Search” function on the receiver. Set the maximum number of channels for your region.

Find the antenna position at which the signal clarity will be maximum. Lock the plate in this position. Tighten the mounting bolts tightly to prevent the antenna from rotating due to strong winds or its own weight.

If you need to reformat any video, a converter is simply irreplaceable. Improve quality, reduce size, adapt to the capabilities of the player. All this can be done in such a relatively easy-to-use program.

Instructions

Download a video converter from the Internet. The most popular versions are from Nero and Genius. They are quite easy to use and have a very wide range of capabilities. Run the application installer. Agree to the requirements license agreement.

Select a directory. If you don't need advanced features, select Standard. This means that some program components will not be installed, since they are not particularly needed. Wait for the installation to complete. Reboot your Personal Computer.

Find the program icon on your desktop. If it was not created there automatically, go to the directory you chose as the installation location. Double-click on the shortcut to launch and then configure the converter. With this program you can not only change the format, but also view the video.

On the toolbar, go to the “View” tab. Add Active Monitor to the workspace of the program. It will be placed in the upper right corner of the program window. While converting a video, you will now be able to view it.

Set the format you will use most often. At the bottom of the program window, find two lines. One indicates the address of the folder where the converted video will be saved, the other indicates the format into which the conversion will take place. Expand the list of available formats. It is orderly and clearly grouped.

Select required format, left-click on it once. After that, you will see how it is listed in the line as used. You can always change it as needed. Load several files into the video converter. This can be done through the open folder or simply drag and drop necessary files into the program window. Start conversion. If changing the current video format to the required one is not possible, select another one that would also meet your requirements.

Video on the topic

A tuner is a special device that can decode an incoming signal and transmit it to the TV in a form that it can understand. Mostly common now satellite receivers, which are part of a complex of equipment for satellite TV.

You will need

• - TV;
• - satellite receiver.

Instructions

To disable comments, you will need to install the RC Link Redirector plugin, which is usually used to turn external links to internal ones by redirecting (redirection), or delete from source code satellite site form for adding links. If you still decide to allow commenting on satellite articles, then additional security install anti-spam plugins on your site, for example, Akismet or DCaptcha.

To set up a satellite site on WordPress engine you can install the following additional plugins: - Simple Tags is used to create, edit and manage tags, through which you can also increase the number of site pages; - RusToLat converts strange symbols, appearing in URLs to posts, in Latin letters;- Dagon Design Sitemap Generator is used to create a sitemap;- Google XML Sitemaps creates an XML sitemap; - All in One SEO Pack optimizes the satellite; - WordPress Database Backup is required to backup Databases and send them to email.

08/21/2017 08/30/2017 by Eve

For independent NTV+ settings You need to take into account the angle of the dish mirror itself towards the satellite: it varies from 17 to 38 degrees. You can find out the exact value from the satellite dish manufacturer or see the attached instructions.

Setting up the NTV+ antenna carried out in the following stages:

1. Point the plate towards the south. On the official website of NTV + you can see that the trajectory of the Eutelsat 36A (B, C) satellites is located on the equator. For precise definition use the compass.
2. Often problems with the quality of the resulting picture are not related to the equipment. It is the presence of interference in the form of trees, houses, towers that prevents the signal from entering or significantly muffles it. For the city, the ideal place for installation is the roof, and for rural areas - a pole. But if there are no obstacles near the installation point, then installation can be done near the window.
3. An important aspect is the fastening: it must be rigid and strong. In winter, when the windage of the dish is most noticeable, a good mount will not reduce the signal level. It is best to secure the plate with stainless steel anchor bolts.
4. Connect the convector to the antenna, and then route the cable to the receiver.

After installation, you must turn on the receiver and set up NTV+ channels. Go to the main menu, select manual or automatic mode, then click “Search for channels”.

Schematically it looks like this: Menu/Settings/Installation/NTV-Plus (auto search). A list will appear in front of you in which you need to select NTV-Plus (auto search). You can also periodically update the installed software manually or specify in advance in the settings “ Automatic update BY".

To manually configure, you need to go to the main menu and select “Default installation”. In this case, the software will work according to the manufacturer’s specified algorithm. Enter the “Channels” item, then directly into the “Antenna” column, after which you will see a list in which you should click “Setting up a satellite system and satellite”.

Next, the tuner will ask for a password, which must be entered manually. After entering the password, a window will appear in front of you in which you need to remove the checkmarks in front of all positions except the desired satellite - Eutelsat 36A (B, C, E). These manipulations are monitored by the system and blocked, so you can remove the operator card from the tuner in advance.

Next step: setting up the transponder. In order for the system to work smoothly, it is necessary to enter the following data into the program:

— Lower level Lnb = 0;

— Upper level Lnb = 10750.

Save the entered parameters and select the required transponder from the list in the “ Manual setting" After that, start searching for channels from the NTV+ operator and add the ones you like to the main list of channels.

There are times when the Eutelsat 36A(B,C) satellite is missing from the list of satellites. In this case, you need to create a new network (User sat 1) by turning on the “LNB Power” function. Set all the necessary parameters and save them without specifying the transponder. Go to the “Manual Tuning” tab and scan the entered satellite. Then create a new transponder with new characteristics. If you did everything correctly, then in the main window you should see new network, under the name "NTV Plus". Now you need to add channels: click the “Scan” button and bind the channels to the transponder.

An excellent choice for all sports and movie lovers. But for the television to operate without failures and interference, you will need to correctly assemble, install and configure the dish. Make sure that the requirements necessary for high-quality operation of the system are met:

• Visibility to the south from a window, balcony or roof.
• An open horizon without interference, high-rise buildings at window level.

NTV Plus channels are broadcast from the Eutelsat W4/Express AMU 1 satellite, located at 36 degrees east longitude. The satellite covers the main part of the territory of the Russian Federation. To receive channels you need a set of equipment:

• Plate with a diameter of 55-90cm.
• Circular polarization converter.
• or cam module.
• Coaxial cable.
• Connectors.

The minimum mirror size for reception is 55-60cm. An increased antenna size of 80-90cm will make the signal more stable; it will not depend on rain, snowfall and cloudiness. In the NTV+ system, circular polarization converters are connected. There should be a circular mark on the body of the irradiator. The number of outputs in the irradiator corresponds to the number of connected attachments.

Let's begin the procedure for installing and configuring NTV Plus channels, which consists of several stages.

Stage 1. Check the signal.

You can set up an NTV Plus satellite dish only if there is a signal. You can navigate by the dishes located in neighboring houses or apartments, by the sun: around 13:00, its direction corresponds to the position of the satellite. There are special maps on the Internet - Dishpointer, which help you check satellite reception. To work with the map, enter the exact address of the house and select the name of the Eutelsat W4/Express AMU1 satellite. A colored beam will show the direction of the satellite. If the satellite is not received from the window, then the system is installed on the roof of the house. The connection will cost more, since cable costs will increase, but the result obtained is worth the effort.

Only a specialist visit and signal measurement using a spectrum analyzer will give an accurate guarantee of availability satellite reception! The cost of these works is 1000 ₽.

How does a satellite TV set work? The antenna plays the role of a lens that receives the signal and transmits it to the converter. The converter amplifies reception and transmits the signal to the set-top box.

Stage 2. Equipment installation.

We assemble the satellite dish according to the instructions. A drill with a hammer drill for drilling brick and concrete surfaces will make the process easier. To attach the bracket, anchor bolts with a diameter of 8mm or 10mm or 14mm dowels with a capercaillie are suitable. All connections are made using a coaxial cable and f connector. The cable is stripped (see photo) and the connector is put on it. Connectors come in screw-on and crimp-on types. The most common ones are for cheating. Crimp connectors are more reliable and have a longer service life, but their installation will require crimping pliers.

After assembling the dish, we set it according to the elevation and azimuth of your region. For Moscow, the elevation angle is 27 degrees, the azimuth is 181 degrees (see photo).

Photo 1	Photo 2

Stage 3. Setting up a satellite dish

We carry out the work using or using a receiver. In the second case, the set-top box will need to be configured in advance. This can be done either by purchasing the system in a store or from a friend who has a working antenna connected. You can configure programs manually or automatic search. In the set-top box recommended by the operator, all the settings are already included in the menu, you only need to select the automatic mode, the receiver will do everything on its own. In manual search, the procedure for entering parameters is necessary:

• Eultesat W4/Express AMU1 satellite.
• Converter settings: upper/lower local oscillator frequency 10750 MHz.
• To search we use a transponder: 11785 R, flow rate 27500, error correction 3/4.
• 22KHz must be enabled to supply power to the converter.
• We activate the network search function to search the entire list of channels.

The channels are configured, go to the "Search for channels" menu. Two scales will appear on the screen: reception level and quality. For the satellite to operate, it will be necessary to fill two scales by at least 70%. We carry out the operation of setting up the antenna in clear, calm weather, if possible at noon, when the sun can be used as an additional reference point.

The procedure for setting up an NTV plus antenna for a satellite

• We direct the dish to the satellite's receiving sector (we focus on the sun and neighbors' antennas).
• We set the mirror vertically (for Moscow/Moscow region), up to the maximum.
• Slowly turn the plate 1-2mm, wait a couple of seconds, look at the signal scales on the screen; repeat the procedure until the scales begin to fill.
• As soon as the scales begin to fill, we proceed to the fine-tuning procedure until we achieve 70% filling.
• Fix firmly and tighten the bolts.
• We carry out all the work slowly, since the receiver reacts late, and you may miss the desired location of the system.

Call a specialist

When the system cannot be debugged or problems arise with the operation of the satellite, the repair and configuration service will restore channel viewing.

The services of a specialist will be needed if:

• The picture and sound are distorted.
• The TV showed "no signal".
• Failed to establish reception.
• The signal is unstable: it is, then it is not.
• Cloudiness, rain, snowfall interfere with reception.

The cost of setting up an NTV antenna plus 2000 ₽ without additional extra charges and surcharges for work!

During repair work, the following consumables may be required:

• Converter with 1 output - 490 ₽.
• Coaxial cable - 35 ₽ per meter.
• Antenna 0.55m - 980 ₽ (if the mirror is deformed due to a hurricane or storm).

All our technicians have specialized technical education and experience in the field of installation and commissioning of telecommunications equipment. The Spectr TV company provides high-quality service for a small fee. All work is guaranteed.

• 
  Arthur
• In the company since 2010. Specialization: repair, configuration, installation of satellite systems

• 
  Alexander
• In the company since 2006. Specialization: repair, configuration, installation of satellite and terrestrial systems

• 
  Sergey
• In the company since 2004. Specialization: repair, configuration, installation of TV systems. cellular. Internet.