We update GS 8306 from USB to the new version 1.9.160, beginning

GS 8306 has waited its turn and we are updating it via USB. For this we have a new version software 1.9.160. Let's see what difficulties there may be during pouring. Because unfortunately updates on the operator's receivers Lately don't go very smoothly.

GS 8306 version p.o. 1.9.160

GS 8306 update process

2. The receiver begins the update process. The entire button is lit, but there is no image on the screen! It is impossible to check the update process on the screen; both receiver outputs do not work!

GS 8306 version p.o. 1.9.160, upper diode.

3. One diode of the receiver lights up constantly, the second blinks occasionally. This is all normal, the main thing is not to turn off the receiver from the network! If you turn off the power now, the receiver will fly far and long!

GS 8306 version p.o. 1.9.160, the update process is complete.

4. After the receiver has loaded everything, both diodes will go off! We wait at least 10 seconds. If you turn it off earlier, the receiver will be damaged! Of course, it’s scary, but that’s how everything is done here….

GS8306 p.o. 1.9.160 inclusion.

5. After everything has been updated, turn off the receiver from the network. We remove the flash drive from the USB. We turn on the receiver and configure all programs.

GS8306 version p.o. 1.9.160 status check.

That's all, we have updated our receiver, now we can watch television programs. The main thing to remember is that during the update our receiver may break and this is not a joke. The majority of users will not be able to repair the receiver themselves.

If you still have doubts about how to update, watch the video. In this video, the entire update takes place in real time.

Let's add another video about this firmware.

Deterioration in signal quality or incorrect setting of Tricolor TV channels may indicate that the receiver software version is outdated. To eliminate control errors, get rid of operational problems and even expand the range of capabilities of the Tricolor TV GS-8306 receiver, you need to update the software. You can cope with this task without contacting a specialist; it will take about a third of an hour, a little knowledge of how to flash the equipment you have at home, and its subsequent configuration.

Preparing for a software update

Before flashing the receiver, you need to make sure that the device reliably receives the signal. Due to the fact that software will be installed directly via satellite, any technical failure could be fatal for the receiver. For the same reason it is necessary to ensure uninterruptible power supply , otherwise it may not turn on the next time you start it.

If you are outside the city in windy weather, a thunderstorm, or during a given period of time there are periodic power outages, then it is better not to risk it and postpone the procedure for a while.

How to reflash the receiver yourself

The firmware will take you about 20 minutes, but at this time you should not neglect the instructions and turn off the receiver or TV. The sequence of actions is as follows:

If you have doubts about your own abilities, as well as fears that the set-top box may no longer turn on due to an interruption in the data loading process, it is better to contact a service center.

The company’s specialists can not only reflash the receiver, but also produce equipment diagnostics. In this case, it is worth finding out in advance about the cost of the services provided and the timing of their implementation.

What will the new firmware version change?

The processes of information exchange and improvement of communication channels do not stand still. In order to improve picture quality and sound quality, developers are working tirelessly to create new software environment. Although the devices in users' homes will remain old, timely software updates can expand functionality and make the interface of the satellite set-top box simpler and more convenient.

Do not forget that a new version of the software for the GS-8306 Tricolor TV model is planned for 2017. This means that you can’t miss the opportunity to have improved quality satellite television in your home or dacha.

Opportunities will open up for you:

• sorting films by alphabet, genre and show time;
• reading descriptions of films and TV series that interest you;
• setting a timer to turn on selected viewing sessions.

Summing up

Now you know exactly how to update the software of your Tricolor GS-8006 receiver . Detailed instructions will certainly help to maintain the correct operation of the equipment throughout its entire service life and not waste money on the help of specialists. In addition, it becomes possible, without changing the device, to expand the functionality of the set-top box and change the interface, which with each new version becomes more intuitive, understandable and attractive.

With the advent of the Internet modern man does not experience information “hunger”. It's easy enough to find the information you so desperately need. However, when reading any instructions, it is important to understand that any deviation from the prescribed requirements is fraught with serious consequences.

When purchasing a new GS 8306 receiver, owners often want to know how to reflash the Tricolor GS 8306 receiver. This desire is truly justified, since the firmware allows for stability in the future operation of the receiver in HDMI mode.

Any user can reflash the GS-8306, the main thing is to strictly follow the instructions and do everything correctly

We can even confidently say that the GS 8306 firmware allows you to successfully cure the receiver from glitches.

Firmware process

Experienced users and experts emphasize to all interested parties that without certain skills related to software updating, you can unknowingly make fatal mistakes.

Why is new firmware needed?

When carrying out any actions, it is very important to understand how important they are, and whether it is possible to do without them in any way. The flurry of people wanting to know how to flash GS 8306 from a flash drive is explained by the fact that new firmware gives the receiver several advantages.

First of all, the device acquires a modernized menu for selecting the desired operator. Also, the “Status” menu after the firmware is accompanied by an updated interface, which makes it easier to work with the menu.

Also welcomed by many is the fact that after the firmware the receiver is characterized by significantly improved performance. Such important manipulations make it possible to display an information block that contains important information regarding payment methods for Tricolor TV services.

The acquired characteristic is especially welcome, allowing you to remember in standby mode the settings that were defined on the receiver before it was disconnected from the power supply.

Firmware installation instructions

If you carefully inspect the design of the receiver, you can make sure that the device does not have an RS-232 (COM) port. However, in return, its receiver has a service USB. It is thanks to its presence that the device undergoes flashing.

For such manipulations, the owner of the receiver should prepare an ordinary flash drive. Naturally, you should take care in advance of downloading the firmware file itself, which can be downloaded on the Internet on specialized forums focused on issues of Tricolor receivers.

After downloading the proposed file, unzip it into the folder you created previously. Then find the firmware itself in it: ssu_gsc_stb.upg.

Initially, format the flash drive that you prepared in advance. Before formatting, the system will ask you which file system you want to install on it, check FAT32. Copy the firmware startup file and paste it onto the USB flash drive.

Now all that remains is to connect the flash drive to the receiver by inserting it into the USB connector. The receiver must be turned on during this procedure.

With the flash drive inserted, first turn off the receiver and then immediately turn it on. This is not difficult to do if you press the “Stand by” button, which is located on the front panel of the receiver.

After turning on the receiver again, the firmware process starts and is carried out automatically. The user can verify that the firmware is actually being installed by the information that appears on the TV screen.

At this moment, you should sit near the screen and do any other things, but not interfere in any way with the ongoing process. When he reaches the finish line, information will appear on the screen indicating the successful completion of the process.

Now you can safely remove the flash drive and reboot the receiver again. It is very important to remember that you can remove the flash drive only after notification of the successful completion of the firmware. If you remove it earlier, serious problems may arise that will be impossible to deal with on your own at home.

And it is also quite important to understand that you can only install the firmware current version or new. Return old version firmware is not possible.

So, flashing the Tricolor receiver GS 8306 can be done by a user who knows how to strictly follow the instructions, has previously read the important requirements and is able to follow all the rules without haste.

Stable work largest operator satellite television Tricolor TV becomes possible only after correct installation and subsequent configuration of components. This process can be carried out by the user independently; just study the current instructions for 2019. When considering how to set up the Tricolor TV Receiver yourself, you should highlight positive traits from the use of custom search and the presence of different generations of models technical devices, the principle of working with which may vary.

In this material we will look at:

• configuration features;
• differences in working with different device models.

Preliminary actions and features of manual channel search

Connecting the receiver is identical for all types of receivers. You must first install a satellite dish, according to the official coordinates for your region, which are offered by the operator. Set the correct tilt angle and route the cable to the receiver.

Classically, there are several connection methods:

• the high frequency connection can be connected using a suitable antenna cable;
• The low-frequency signal is received and transmitted using a classic scart cable.

Having connected the wiring and ensured stable operation, you can proceed with further registration and search. If the device does not function correctly, you can try to independently search for the necessary information in the corresponding technical section of the official website or contact a support specialist. This can be done by toll free number, or using the functionality of additional software.

How to set up Tricolor TV channels yourself on the GS 8306 receiver

GS 8306 is a popular model among telecommunications operator clients, capable of displaying images in HD quality. The smart card here is installed in a separate slot, which expands the possibilities of using the device.

The configuration is done in the classic way:

1. Open the "Settings" menu;
2. Select the “Search” section, click on the “Manual” item;
3. Fill out the proposed field by entering operating frequencies;
4. Repeat the action as many times as necessary until all channels are added to the database;
5. Save your changes and reboot your device.

Manual search has a positive effect on the following factors:

• good quality of the broadcast image with correct installation satellite;
• increased speed of receiving and transmitting data packets.

Setting parameters yourself takes more time and requires searching additional information. The list of frequencies and other parameters are located in the technical section of the official website.

How to configure the DRS 5001 Tricolor TV receiver yourself

Though specifications drs 5001 and are inferior to some modern analogues, this device is still in high demand among customers. Timely release of software updates contributes to the implementation of current software capabilities, which indicates high quality service and individual approach to each client.

When considering how to set up the Tricolor receiver, it is worth first noting that the technical equipment is connected identically, which indicates a similar operating principle. This configuration implies:

• registering the receiver on the website or in your personal account;
• synchronization with satellite and channel search.

Registration is a mandatory action for all clients of a telecommunications operator. To do this, simply enter the smart card ID, consisting of a combination of 12 or 14 characters, into the appropriate field on the control panel. Additionally, indicate the receiver number and personal contact information.

If everything is done correctly, information about technical components and personal data will be added to a secure database, after which you can set up channels for everyday viewing.

Setting up the GS B520 Tricolor TV receiver

GS B520 is a new generation of operator supplied equipment. Become the owner of this technical solution every client of the company can by taking part in the program to replace outdated technical components.

The main advantages of a modern set-top box include:

• the ability to broadcast the stream to mobile devices;
• connection to home Wi-Fi networks for data exchange;
• a full set of modern ports - USB, Ethernet, HDMI and others;
• interface for connecting a storage device with the subsequent ability to record the broadcast;
• access to “Cinemas”, “Games” and other unique offers from Tricolor TV.

Preparation for use is carried out in the usual way: after connecting to a satellite dish, the user needs to register the device in the common database. Channel tuning can be either automatic or manual mode. Using custom parameters will allow you to independently divide channels into categories and simplify access to them. Don't forget to save the changes before rebooting the device: incorrect execution of the data may cause the software to malfunction.

How to configure the GS B211 Tricolor TV receiver yourself

Setting up the Tricolor TV receiver yourself for the technical equipment model gs b211 is done in the same way as the above method. Modern device allows you to broadcast a high-quality signal with the possibility of duplicating it to other devices. Detailed technical information and help on the issue of interest can be obtained on the official website of the operator.

In their work, Tricolor-TV systems use receivers that decode the signal coming from satellites. For their proper operation apply operating firmware, which need to be updated from time to time. GS 8306 is one of the most common receivers among Tricolor-TV subscribers, so if you use it, like many other users, you need to be able to install upcoming updates to its system.

Updating receivers, as well as other equipment intended for decoding digital signal, need to:

1. All systems for connecting to the satellite and to the TV worked as efficiently as possible - the best picture was shown, a list of channels was available, etc.
2. Possible problems with previous software have been eliminated and have ceased to bother users.
3. Implement new functions, codes and capabilities into the system.
4. Simplify the interaction between the user and the interface - make the program interface more convenient and understandable.
5. Check the functionality of the old system and clean out the accumulated “garbage”.

If you do not update the software, interruptions may occur over time with the broadcast of TV channels. Errors on the screen will appear more and more often, blocking access to viewing. If the smart card and receiver software do not match, “Error No. 5” will occur and viewing will be impossible. And even the coordinated operation of the receiver and TV may be at risk.

Algorithm of actions

You can update the receiver software in two ways:

1. Using the distribution package downloaded to a USB flash drive.
2. Using a satellite connection.

Using a flash drive

To update the receiver of this model in this way, you must:

1. Check whether you need an update - to do this, in the “Information” menu section, view the latest firmware version and run a check for update availability.
2. If updates are available, turn on your computer and go to the website: http://www.gs.ru/support/manuals-and-software/GS-8306/. Here is the official software for digital receiver– and only from this site is it recommended to download licensed software for GS (GeneralSatellite) models.
3. Upload the downloaded content to the flash drive - the files must be in the root directory, and the flash drive itself is formatted in FAT32.

Important! Do not change the names of the update files under any circumstances.

1. Connect the USB flash drive to the turned off receiver, and turn on the receiver.
2. Take a close look at the LEDs around the power button. After turning on the receiver in this way, both LEDs will blink, after which one will go out, and only the top one will remain on. The lower one will flash periodically. This is a sign that this moment The system is being updated.

Important! Information about the update progress will not be displayed on the screen, so watch the diodes!

1. The software update takes approximately 5 minutes - when completed, both LEDs will turn off.
2. Wait 10 seconds or more before removing the USB flash drive.
3. Take out the flash drive. She is no longer needed.
4. Unplug the receiver from the outlet, and after 10-15 seconds turn the power back on.

The update is complete, you can see the new software version in the menu.

Attention! The features of the GS 8306 receiver will not allow you to “roll back” to the previous version of the software if difficulties arise with this one during installation.

By satellite

Updating via a standard satellite connection is much easier and more user-friendly, but issues are more likely to occur during installation than updating from USB.

To avoid violations during the update, follow the instructions strictly:

1. Start with a new channel search, and save them when you finish the procedure.
2. Turn the receiver off and on by removing the plug from the outlet and putting it back in place.
3. Turn on channel 333 - it will be informational.
4. Wait a couple of seconds - the system will check for updates and inform you about their availability. The message will also indicate the new software version.
5. Select Yes.
6. Wait until the second stage of the update is completed.
7. Wait for the receiver to reboot.
8. After the last reboot, the Setup Wizard will appear on the screen - select the language, time, operator, region.
9. Search for channels.
10. Ready! After the installer completes its work, the new software version will be displayed in the “Status” menu item.

Important! Do not reboot or disconnect the receiver during the installation process. This may result in the system not being fully updated and you will not have access to viewing.