The zte zxhn h108n router released last season has found wide use in networks largest operators communications. The Ukrtelecom provider is no exception, which recommends purchasing this device to connect to its network and rents it out.

The modem supports Internet connection via ADSL technologies. It can provide access to global network four subscribers via a wired interface, and the device is equipped WiFi module to create wireless connections.

The presented instructions will show how to configure the zxhn h108n or a similar device zxv10 h108l to work with the Ukrtelecom provider. It is worth noting that the algorithm WiFi connections The router connection to other telecom operators is not very different, so the instructions will also be useful to users of other networks.

To connect WiFi router and to the Ukrtelecom network using ADSL technology, perform the following operations:

Connect the power supply to the Wi-Fi modem via the “Power” connector, then plug it into the electrical network.

Connect the “Line” port of the splitter included with the WiFi router to a telephone socket. Connect the zxhn h108n or zxv10 h108l to the “Modem” port, on which the required socket is marked “DSL”. Connect a telephone device to the “Phone” port, if you have one and have concluded an agreement with Ukrtelecom for the provision of this type of communication.

To configure the parameters of zte zxhn h108n or zxv10 h108l, connect your computer to it via an Ethernet cable (included). To do this, use the “LAN1” port on the Wi-Fi modem, and on the PC the network card connector.

Computer settings

In cases where the computer is connected, and the corresponding LAN indicator on the front panel of the WiFi router does not light, you should configure the PC’s network card.

Windows 7

Through “Start”, activate “Control Panel” and click on “View network status and tasks”.

Click on “Change adapter settings”.

Right-click on the active connection. A list will appear where you should select the “Properties” value.

Double click on “Internet Protocol Version 4 (TCP/IPv4)”.

Switch the dialog flags to the states shown in the following figure.

Commit the changes by clicking “Ok” in all open windows.

In Windows 8 (eight), the setup is performed in a similar way, but in order to open the “Control Panel” you need to right-click on the “Start” menu and select “All applications”, where the necessary link will be.

Internet connections

Setting up a zte zxhn h108n or zxv10 h108l for Ukrtelecom is better from the factory settings, so the parameters of a used modem should be reset. To do this, press and hold the “Reset” button recessed in the device’s body for at least ten seconds, and then wait for it to reboot.

The modem connected to the network using ADSL technology and to a computer via an Ethernet cable is configured using the following algorithm:

Log in to the device’s web interface using an Internet browser; to do this, type the link 192.168.1.1 and start clicking on it.

Open the browser, enter address bar http://192.168.1.1

login and password for the router admin\admin

In the main window of the Wi-Fi router interface, find the link to the “Interface Setup” tab and click on it, and then on the “Internet” settings item.

DHCP

To configure a DHCP connection, change the field values:

PPPoE

To configure a PPPoE connection, the fields change:

Once you have completed setting up the required connection, save the changes by clicking “Save”.

To make the change take effect, restart the WiFi router by going to the “SysRestart” item in the “MainInterface” tab. Here select “Current Setting” and click on the “Restart” button.

Wait until the zte zxhn h108n or zxv10 h108l reboots and access the Internet from your computer using ADSL technology.

Wi-Fi setup

To enable the provisioning feature wireless access To connect to the Internet via WiFi, you should perform a number of additional steps:

In the web interface of the Wi-Fi router, go to the “Interface Setup” tab, where open the “Wireless” item.

Set up the following page fields:

• "Access Point": Activated;
• "Wireless Mode": 802.1 1b+g+n;
• "Chanel Bandwidth": 20/40 MHz;
• "SSID": The name of your network shown in the list available connections on subscriber devices. It is chosen arbitrarily, but only numbers and Latin letters are allowed;
• "Authentication Type": WPA2-PSK;
• "Encryption": TKIP/AES;
• “Pre-Shared Key”: arbitrary network password, numbers and Latin letters are allowed.

Save the changes by clicking the "Save" button and rebooting WiFi modem according to the algorithm specified earlier.

Wait until the reboot completes and connect your Wi-Fi devices to the Internet.

Found a typo? Select the text and press Ctrl + Enter

To configure any of the routers in the ZTE line, it is first recommended to prepare Rostelecom Internet connection authorization data, since it will not be possible to activate the network without them. In most cases, the provider uses PPPoE type of connection to services. These parameters are used to establish communication using ADSL and Ethernet technology. There are also less common options for connecting services that can be used when running a fiber optic cable directly into an apartment or a private house client.

Configuring Rostelecom parameters for ZTE brand routers

ZTE is one of the largest companies in the global electronics market. In addition to received in Lately the enormous popularity of the manufacturer’s smartphones, which have a lower cost than similar products from the LG and Samsung brands, but at the same time are not inferior to them in terms of characteristics and quality, the company also takes a strong position in the field of network equipment.

ZTE provides its customers with a wide range of devices to create home or corporate network. For users who need the Internet outside the city, where it is not possible to create a wired connection, the manufacturer offers ZTE MF 190 modems, distributed both with native (factory firmware) and with an already built-in modification from Rostelecom.

These can be connected directly to a computer or using routers that support the appropriate connector and technology.

Attention! There is no possibility to reflash ZTE MF 190 modems from Rostelecom or other operators using official methods. For such tasks, the Dc-Unlocker program is usually used.

ZTE also has routers in its line of network equipment, for example, the H108N, which is adopted by users as a Rostelecom Ethernet modem for setting up high-speed home and work networks.

Preparing to set up equipment

Before setting up ZTE routers under Rostelecom, for example, model E5501, you need to check the equipment package, which contains:

• power supply (12V converter);
• at least one Ethernet cable.

Of course, the newly unpacked box from the device will also contain a software disc, a warranty and a lot of literature, but for setting up a ZTE modem under Rostelecom, these components do not play an important role.

Attention! Even if you want to use the Internet only via Wi-Fi, an Ethernet cable is in any case an indispensable component that is needed for the initial setup.

To connect the device, the first thing you need to familiarize yourself with is the ports on the rear panel.

Turning the ZTE E5501 around with the side with the functional connectors, just like on the ZXV10 W300, you can find:

• four LAN ports;
• Ethernet port;
• connector for power cable.

The ZTE H108N model will have one difference from the above modems, namely a connector for an ADSL cable (telephone cable), since this router is designed for the Internet via telephone line. This will not significantly affect the overall sequence of connecting network equipment. First of all, we connect the power supply to the outlet and port on the router, and then insert the Internet cable into the WAN or ADSL port (depending on the modem model, one of these ports will be present). Now we find an RJ45 connector on the computer (standard network input) and connect it using an Ethernet cable to the corresponding port on the router. Since in our case there are four connectors, you can connect the cord to any one.

Attention! If you are setting up a ZTE H108N, then in addition to the described sequence, it is also recommended to connect a splitter that filters the Internet and network signals. This will allow you to use two provider services simultaneously.

When all the cords are connected, you can turn on the equipment, which is done using the button on the rear panel.

Now let's move on to the front part of the device. It contains indicators that will help you find out about the status of the options when setting up ZTE ZXV10 W300, H108N or E5501 modems for Rostelecom. For example, data is displayed here:

• which connector is the computer connected to?
• Is Wi-Fi working?
• Is there a connection to the provider and the Internet?

Setting up an Internet connection on ZTE ZXV10 W300, ZTE H108N, ZTE E5501

When the connection part is completed, you can move on to setting up modems for Rostelecom, which we will do using the ZTE ZXV10 W300 as an example. We go from a computer connected directly to the modem to the browser and enter the router’s IP in the address bar. You can find it in the equipment passport. In our case it will be 192.168.1.1. Now enter the standard login and password, which are also indicated in the instructions for the modem (admin/admin).

After this, you will be redirected to the device software control panel. In the Network tab, select WAN parameters and configure PPPoE connections according to data issued by the provider. They can be found in the contract or on a special Rostelecom card.

Since the equipment supports Wi-Fi settings and such a modem is usually purchased with the intention of connecting wireless devices to the network; you can configure the operation of the module on the Wireless tab. Here we select the network name (SSID), and also create a security key that will prevent unauthorized clients from connecting to your wireless network.

From ZTE, depending on its type (portable or stationary), it is produced in several stages. When installing routers for private apartments or small offices, a suitable location is first selected, then the connection is made, and then the connection parameters are entered.

How to connect ZTE?

As a rule, advanced users do not have problems connecting and configuring ZTE modems. But even experts sometimes have to resort to saved notes in order to remember one or another step of installing a modem.

Therefore, in this article we will tell you how to connect a ZTE modem to a computer so that you can configure the device at any time.

Connecting the modem

To do this you will need the following list of equipment:

• Computer or switch;
• Connecting cables;
• Splitter;
• ADSL modem.

Let's move on to the connection process:

1. Turn on your PC and wait for the operating system to load.
2. Connect the modem to a switch or PC. Take an Ethernet cable and connect it to one of the LAN connectors on the switch or network card in computer.
3. Connect your modem to the telephone line through a splitter. This is done by connecting the connector on the modem, where it says DSL, to the connector on the splitter, where it says MODEM. To do this, use the telephone cable provided with the ZTE modem.
4. Connect the LINE connector (on the splitter) to a telephone socket. Please note that if you have old-style sockets with five pins, you will need to buy an adapter for a European standard connector.
5. Connect the cable from your phone to the PHONE connector on the splitter.
6. The power adapter must be connected to the modem. To do this, take your modem and connect the appropriate cable to the power supply. Press the power button. If everything is connected correctly, after booting three lights on the modem should be on - one of LAN, as well as DSL and POWER.

Setting up a modem to connect to the Internet

Everything is quite simple here. After you connect zte modem, start setting it up:

1. Open any of your browsers and enter command line address IP address of your modem (192.168.1.1);
2. Now we enter the username and password. The default values ​​are admin. This is both a name and a password. Click OK;
3. Go to the Quick Start section and enter the username and password there that your provider provided to you, then click on Connect;
4. If the connection was successful, you will see the corresponding text on the screen, as well as the Disconnect button;
5. If you wish, you can change the password and login name for your modem management window. To do this, go to the Management section, write a new name and password and complete the change with the Apply button.

Nowadays, almost everyone who has a PC, laptop or tablet in their home uses the network. We recommend that you study the section, which will allow you to understand the general rules and recommendations for successful work on the network.

Question: How to set up Internet on ZTE smartphones (phones) and tablets?

Answer: Setting up the Internet on ZTE devices is performed in the following order.

1. We connect the service to the operator. This can usually be done via USSD request.

To connect to the Internet from Megafon, we recommend following the link - http://www.megafon.ru/internet/, select the type of device to connect, for example - “For smartphone”, select your region, then select a tariff, click “Buy”, then When information appears, what code you need to dial to activate the service, for example - *236*0#. We dial this code like a regular telephone number.

To connect to the Internet from MTS, we recommend following the link - http://www.mts.ru/mobil_inet_and_tv/, select the type of device to connect, for example - “Internet from phone”, after which a page will open with a code that you need to dial to connect services, for example - *252#.

To connect to the Internet from Beeline, we recommend following the link - http://beeline.ru/customers/products/mobile/, select the type of device to connect, for example - “On phone”, then select tariff plan, then click on “To connect” -> “Connect and manage the service”, after which you can see information on how to connect the service, for example, by dialing the code - *115*04# or by calling the number.

Attention! Page addresses and USSD request codes are provided for illustrative purposes only and may change over time! To connect, go to the main page of your website mobile operator and already with home page go to pages with information about Internet connection. For other operators, the settings will be approximately similar. You can also call your mobile operator at hotline and activate the service verbally. Another option is to go to any operator’s sales office in your city, where the sales people will be required to connect you to the service.

2. To turn on the Internet, you need to go to “Settings” -> “Data transfer” and opposite the “Mobile” item. traffic" or check the enable box, or move the switch to the right to "On". For most ZTE smartphones this is enough to automatic switching on mobile internet. After the connection is established, depending on the type of connection, the symbol H (HSDPA), G (GPRS), E (Edge), R (Roaming) or 3G will appear in the notification panel next to the network signal strength icon. Also, to check the Internet connection, open the browser and wait for any Internet page to load, for example by typing “ya.ru” (a light version of Yandex) in the address bar.

Attention! If ZTE smartphone 2 SIM card, then the SIM card that will be used to access the Internet must be inserted into the WCDMA/GSM connector, and in the settings “Settings” -> “More” -> “ Mobile network» -> « Network settings SIM1″ (or 2 depending on the model, see the slot number under the cover) -> “Network mode” -> “Preferred network mode” -> “GSM / WCDMA” or only “WCDMA”.

3. If the Internet on your ZTE device still does not appear after following the previous recommendations, then you must either obtain Internet settings from your cellular operator in automatic mode, or enter the settings manually.

Automatic setup

If the operator is Megafon, then go to the website - megafon.ru, click on the link "Support" -> "Settings", there select "ZTE", and then your smartphone model, for example - "V880E" and enter your phone number. After this, the settings should arrive on your device.

If the operator is MTS, then go to the website mts.ru, then “ Mobile Internet and TV" -> "Help and service" -> "Settings" -> "Phone settings". There we enter the number and wait to receive the settings.

If Beeline operator, That automatic setting mobile Internet can be ordered by a free call to number 0880. (The password for saving settings is 1234.)

Manual setting

If the operator is Megafon, then go to the address http://labs.megafon.ru/dev/, there we select “Other manufacturers” -> “ZTE”, look for your device, for example “ZTE Nubia Z5″, and try to configure it like this, as it is written there.

If the operator is Beeline, then go to the website beeline.ru, there click on the link “Help and support” -> “Internet setup” in the search field enter the model of your device, for example - ZTE V790 and then click “Find instructions” and read the information on at a construction site. You can also send instructions directly to your phone by selecting the “Send SMS with instructions for ZTE V790” link.

If the operator is MTS, then go to the website mts.ru, then “Mobile Internet and TV” -> “Help and Maintenance” -> “Settings” -> “Phone Settings” -> “Internet” -> “Android”, read the instructions .

General rules for manual configuration

Go to the “Settings” -> “More” -> “Mobile network” section. If 2 SIM cards are used, then select the settings of the SIM card for which the Internet is activated. Next, click on the item “APN access points” -> “New access point” and enter the settings that are indicated on the website of your cellular operator. After entering the settings, save the access point, reboot the device and rejoice.

In most cases, it is enough to set the following settings.

Router. Its main task is to provide the user with Internet on the go or in the absence of available connections. It is equipped with its own battery, which allows you to use the network for a long time without recharging. But about this and others technical specifications devices just below.

Description

Capable of working in 4G networks. It is produced by Chinese company ZTE. In Russia, this router is actively sold by the Beeline company with locked firmware for use in its networks. average cost of this device is within 3 thousand rubles in the offices or representative offices of the provider. ZTE MF90 is equipped with a battery with a capacity of 2300 mAh. This allows it to work away from power sources for 6-7 hours. In ZTE MF90 you can install additional card MicroSD memory up to 32 GB. To avoid interference at 2.4 GHz frequencies, the device can operate in the 5 GHz band. You can simultaneously connect up to 10 different devices to the ZTE MF90 4G router.

Appearance

The size of the ZTE MF90 mobile router matches its portability, it is slightly larger than an ordinary pack of cigarettes. It looks like a small white box, without any decorative or design flourishes. The body contains only the most necessary parts and elements. The front panel has a small screen with indicators. Below it are two buttons - one of them is responsible for power, the other for connecting using VPS technology.

On one of the edges of the device there are two antenna sockets, protected by special plugs, as well as a microUSB connector for connecting to a computer.

What's inside?

Most of the interior of the device is occupied by the battery. If you remove it, you will find a slot for a regular-sized SIM card and a slot for a memory card.

By the way, to open the device case, you need to slightly move the lid a couple of millimeters. The pressing area is indicated by a small triangle located at the bottom.

Device management

Almost all settings are set via the web interface. However, some of them are transferred to the shoulders of external controls. In particular, in order to turn on the device, you need to hold down the power button for 5 seconds. A short press wakes the router from sleep mode, which by default turns off after 10 minutes of inactivity.

The WPS button, in addition to creating a secure Wi-Fi connection, can also disable the wireless network module.

Three indicators display the current state of the device. Each of them can identify different situations:

• The first indicator is battery charge. If it doesn’t light up at all, it means the device is either turned off or in standby mode. A green signal will indicate that the battery is charged or has a slightly more than average charge. If the green light starts flashing, the battery is now in charging mode. Accordingly, lighting and flashing red indicate the need to connect to a charger.
• The next indicator is the network signal strength. It is usually indicated by several parallel lines arranged according to height. Blue color is defined for working in 4G class networks. Flashing means data is currently being transmitted. The same thing works for a 2G or 3G network, only the color will be green. A red signal indicates an error, no Network or an uninstalled SIM card.
• Well, the last of the indicators is Wi-Fi network. It has only 2 states. When it flashes blue, Wi-Fi is on. When it's just on, WPS mode is activated.

Actually, more extensive information can be obtained in the web interface. There you can also find out about the number of connected users, frequencies used, the exact percentage of battery charge, traffic volumes and other useful information.

Web interface

You can get into the ZTE MF90 settings at the address 192.168.0.1 by entering it in the address bar of the browser. By default, the login and password for logging in is admin. After entering the data, it will be displayed start page configurator. Here it is immediately recommended to set a new password on the ZTE MF90.

The title page displays a lot useful information. Here you can read SMS messages received on the modem and determine the duration of the active session, including the number of bits received and sent. You can also go directly from here to Personal Area or check your balance. But in most cases, users are interested in the setup process; for this, there is a separate menu item with the same name.

As a rule, in most routers the connection is already configured. That is, immediately after inserting the SIM card, the Internet will be available. Of greatest interest is Wi-Fi distribution. To do this you need:

1. After going to settings, go to the Wi-Fi tab. Traditionally, there are several fields that need to be filled out. The very first thing is the network name. This is what will be displayed on other devices when the access point becomes active.
2. Just below this field, you must remember to switch the switch to “On” mode.
3. Next, you should specify the type of network encryption. As a rule, you can leave WPA-PSK. Or set this mode if it is not specified by default.
4. In the “Password” field, you need to select a phrase that is resistant to brute force. This is what will be used when connecting other devices to the router.
5. Next, you can specify the number of maximum connections. If you plan to use the router at home, you can set the number to 10.

In this simple way you can set up a router for home use.

Firmware ZTE MF90

In order to wean the router from the Beeline operator, you will need to unlock it. This procedure is quite complex and requires a large amount of software. Therefore, it is better to turn to the Internet for all the details. In particular, the 4pda website has a couple of detailed and understandable instructions. After successful firmware installation, the router will be able to use a SIM card from any operator.

To increase signal reception power, you can connect an external antenna to the ZTE MF90. For this purpose, the ts9 connector type is used. Large selection of different power external antennas can be found on specialized Internet portals on the Internet.

As mentioned earlier, the router can use a microSD memory card. To access files, you need to use the web interface. There is a separate section for this with the same name.

Not long ago in the store free applications For Android Play Market utility appeared ZTE WiFi Monitor. With its help, you can monitor the status of the router’s networks or change its settings directly from the smartphone screen.

Some reviews

Owners of this router note its convenience and ease of use. Also an undoubted advantage is the ability to unlock and install other firmware. Portability of the device is one of the key factors. This advantage is noted by almost every owner.

The charge, according to users, is kept satisfactorily; for some it is enough for a whole working day. True, just for surfing. If you watch videos on YouTube or download heavy torrents, then this time is halved.

As for the minuses, there were some. Some people are a little annoyed by the white color of the device, which gets dirty after just a week of intensive use. Periodic glitches of both Wi-Fi and the Internet connection in general are also negatively noted.

Implementation appearance, or rather, the LED indication, let us down a little. Many people think that it could have been done better. Several users also noted some dampness and imperfection of the firmware. This is expressed in small failures and glitches.

conclusions

Considering all the pros and cons of the device, we can conclude that with a constructive approach to the router and minor modifications, you can get an excellent and stable device. The autonomy of the router is not bad, the settings are mostly clear and simple. The price is incredible. Overall a pretty good device.