Super simple tablet stand made from a disc container. Tablet stand Homemade tablet stand

If you use a computer tablet for a short time, for example, checking email, checking exchange rates or looking at the weather forecast, then your hands do not have time to get tired. When watching a movie, reading a book or chatting on Skype, you have to look at the screen for a long time. The tablet has to be held in your hands at a certain angle and, despite its light weight, your hands get tired.

To use the tablet in a comfortable environment, it is placed on a stand. Despite the primitiveness of the device, the price of the stand is often more than 10% of the cost of the tablet, although it can be made with your own hands from scrap material in half an hour.

Some people wonder, what is the difference between a tablet and an iPad? The answer is simple, the iPad is the same tablet as any other, just released by the American corporation Apple. Thus, the proposed homemade stand is suitable for supporting any device, including an iPad tablet.

There are many homemade tablet stands offered on the Internet, from the simplest ones made from a sheet of cardboard or an egg carton, which are impossible to look at without tears, to ingenious lever designs. There was even a stand made in the form of a soft pillow. Such thermal insulation is extremely undesirable, since the tablet generates heat during operation, and in hot weather it will overheat, which can lead to slowdown of the tablet and even its failure.

As a result, I haven’t found a simple, elegant and comfortable tablet stand that I would like to repeat. Therefore, I came up with and made my own version, which I bring to your attention.

Design of a homemade tablet stand

The idea arose to make a stand for the tablet from sheet thermoplastic (softens when heated) plastic, from which cases are made modern TVs, printers and other household appliances.

Before starting the manufacture of any homemade product, the first step is to draw a sketch or drawing. In the process of completing the drawing, all geometric dimensions are clarified and new ideas often arise. The photo shows a drawing of a stand for a tablet with a 10.1” display diagonal. If the stand is planned to be used to install a tablet on it smaller size, cell phone or iPhone, then the dimensions must be proportionally reduced.

A price tag holder made of transparent plexiglass 2 mm thick of a suitable size caught my eye. To make a beautiful and convenient stand, it was enough to cut off the excess part from it and bend the edge to support the tablet.

The stand was required for an Acer A500 tablet with a display diagonal of 10.1”, height 177 mm, width 260 mm and weight 765 g. The tablet was attached to the holder at the required angle, and a line was marked on the plexiglass where the stop should be. At a distance of 12 mm from the stop line, a second line was drawn, in the photo on the left, along which it was necessary to cut off the excess part of the plate.

Plexiglass and any other thermoplastic plastic can be sawed well with a hacksaw. But it is much easier and faster to cut off the excess part with an even end using a homemade cutter made from a broken blade from a hacksaw. To do this, the end of the file is sharpened at a right angle on an emery column, as shown in the photograph. It is better to make a cutter with two cutting edges, one of which is thinner for cutting thin sheets.

Next, a metal ruler or any metal plate with a smooth edge is placed along the cutting line and a groove is cut along it in the plastic with the cutter's cutter to a depth of slightly more than half the thickness of the sheet. Typically up to 20 passes are required. The cutter should be moved smoothly with slight pressure.

After obtaining a groove of sufficient depth, the sheet is placed on the edge of the table so that the groove runs along the straight edge of the corner of the tabletop. Now it is enough to press the sheet to the table surface with one hand, and with the other hand bend it relative to the groove line and the plexiglass will crack exactly along the line. Now all that remains is to bend the plexiglass along the intended line to create a support for the tablet, and the stand will be ready.

How to bend plexiglass using heating method

At temperatures above 100°C, plexiglass begins to soften and can be given any shape. Therefore, in order to bend a sheet of plexiglass to make a stop, you need to heat it along the bending line to a temperature of 120-180°C.

At home, you can heat a narrow strip of plexiglass sheet in three ways: using a linear heating element, heated nichrome wire and the hot air of a hair dryer. It is unacceptable to heat plexiglass above a temperature of 260°C, as it may ignite.

Bending plexiglass is a leisurely job. To bend plastic using a heating element or nichrome wire, plexiglass must be placed above them on a short distance so that the bending line is exactly above the heat source. Next, supply voltage is supplied to the heater. You can bend plexiglass only when it itself begins to bend under its own weight.

Since to make the stop in the stand it was necessary to bend a strip of plexiglass 10 mm wide, a hair dryer was used for heating.

In order to heat only a narrow strip of plexiglass, it is necessary to protect the rest of the sheet from heat. To do this, you need to clamp the sheet between two wooden slats or thick plywood, leaving only the part intended for heating protruding. You can tighten the slats using clamps, as shown in the photo, or two self-tapping screws.

Next, using a hairdryer turned on in the minimum heating mode, the strip of plexiglass is evenly heated along its entire length for 1-2 minutes. When the plexiglass softens and floats, which is clearly visible to the eye, the hair dryer turns off, and the strip is quickly bent into shape using a wooden plank. right side. You need to keep the board pressed for several minutes until the plexiglass cools down and becomes hard.

The photograph shows a strip of plexiglass bent at a right angle. The stop is bent and the clamps can be released.

The tablet stand is almost ready. All that remains is to remove the sharp edges from the ends and corners using fine sandpaper. In my case, it was possible to do without the operation of bending the plexiglass. The workpiece already had given form, and to create a stop it was possible to glue a strip of rubber or a couple of narrow strips cut from the remains of plexiglass. But I preferred, nevertheless, to perform the emphasis in the manner described above. It turned out reliable and beautiful.

To prevent abrasion of the tablet body where it rests on the stand, its edges can be covered with tape or tape, as in the photo. Instead of tape, you can glue a strip of any soft fabric.

The width of the stand is made slightly smaller than the width of the tablet, so that it does not interfere with picking up the tablet if necessary. In this photo, the tablet is moved to the right so that you can see the stand structure in detail.

As operating practice has shown, thanks to the presence of a flat support, the stand holds the tablet steadily when installed either on a flat hard surface of a table or a soft sofa cushion, or on your lap. The photo shows a view from the back of a homemade stand with a tablet installed.

The stand, the assembly principles of which are clearly demonstrated in this step-by-step master class, is notable for the fact that it can be used on the floor, at the table, and even lying on the bed. The tablet will always be in a position convenient for you. The design is not only transformable, but also not expensive in terms of cost.

Materials

To make a tablet stand with your own hands, prepare:

PVC pipes, 0.5 inches in diameter;
PVC elbows, 90 degrees, 6 pcs.;
PVC elbows, 45 degrees, 2 pcs.;
T-fittings, 5 pcs.;
3-strip elbows, 4 pcs.;
end caps, 2 pcs.;
rubber washers for the hose, 6 pcs.;
fine-grained sandpaper;
screws 10-24, 3-inch (4 pcs.), 2.5-inch (1 pc.), 2-inch (1 pc.);
nuts for screws, 6 pcs.;
roulette;
drill and drill bits;
PVC pipe cutter or hacksaw;
wing nuts;
glue for PVC materials;
marker.

Attention! The dimensions given may vary depending on the tablet model. IN in this case the stand was made for iPad 2.

Step 1. Principles of fastening and processing of materials

After cutting PVC pipes into the lengths you need, be sure to process the edges of the cuts sandpaper. Treat the edges of the drilled holes in the same way. This way, your work will look aesthetically pleasing, and the surfaces of the assembled stand will not scratch anyone.

When drilling, be sure to make a kind of notch in the hole using a hammer and nail. This will make your task easier, since the material itself is slippery and the drill easily jumps off without such a stop.

When assembling, you first need to simply assemble the parts, then put them on glue or fasten the structure with screws in the places where they are provided for in the design.

Step 2. Building the frame

The frame in this homemade product is the part that holds the tablet itself. It is shaped like the letter “T” with a small inverted “t” at the base. In fact, you need to cut the PVC pipe into three larger parts and connect them with a T-fitting to each other; in the lower part, two small parts of the pipe of the same diameter should be secured with the same fitting.

At the ends of the resulting figure you need to secure three-stripe elbows. For fastening, use screws with wing nuts. Don’t forget to insert a rubber washer between the materials, which will allow the parts to fit as tightly as possible and not creak later.

In the upper part of the frame, be sure to drill one more hole at each edge. Thanks to them, you can rearrange the top mounts and install the tablet in a horizontal or vertical position.

Step 3. Create the main stand

The design of the stand is such that it can easily stand on flat surfaces and is convenient when working with the tablet while lying in bed.

The dimensions of the stand and the assembly diagram itself are shown in the photo. Pay attention to what fittings are used at different pipe connections. When assembling pipes and fittings in the areas indicated by the red arrows, do not use glue.

Step 4. Assembling the stand

The third component of this design is a mini-stand. You will need it to place the tablet on the table if you do not need additional lifting. With its help, the frame is attached to the stand. All parameters and principle of connecting pipes and fittings are shown in the photo. Be careful when connecting the frame and stand with screws, do not tighten the parts tightly together. You should still have easy access to the wing nuts to adjust the orientation of the tablet.

The tablet stand is ready! If you wish, you can improve it by adding elastic bands to the case that will hold your headphones or charger cable.

It happens that you urgently need a tablet stand, but you don’t have time to look for the nearest store of electronic equipment and accessories. Then in a matter of minutes from available means, and for this you do not have to be a craftsman or a sculptor. All it takes is a little patience and ingenuity. And if you are interested in making, for example, a holder case, then you have come to the right place. In any case, see how you can make such a stand yourself.

Simple holders

Stands made of wood and other materials

To make a tablet holder from wood or other materials, you need to remember that during the manufacturing process you may need tools such as a saw, sandpaper, knives and the like, so be safe and be very careful.

It must be said that not all holders are made according to the same design; everyone just customizes the accessory to suit themselves. This could be a stand with an extension in the form of a mini-table for food. Or arrange a bottom for the stylus on the right. In addition, you can provide a compartment for inserting a keyboard, then your tablet holder can be turned into a full-fledged computer station.

Stand case

And, of course, the most popular type of tablet case today is a case in the form of a book-stand. Such an accessory can be made with your own hands at home. Be patient and necessary set tools: leather (or any facing material), rigid plates (you can use cardboard or other hard material), rubber band for fastening, pencil, ruler, scissors, double-sided tape, glue, cardboard paper. As you work, you will see for yourself which tools you may need and which ones will be more convenient to work with. Now let's get down to business.

We have considered almost all possible combinations of stands. As you can see, many of them have a similar design, and therefore, you can play with them in any way. Open the door to your fantasy world and take the initiative. Perhaps you can come up with a very interesting and original tablet holder. It all depends on the skill of your hands and the boundlessness of your imagination. Be creative with the process and you will get the most out of the result.

Tablet or small netbook popular gadget Nowadays. Here is a current idea in the topic "".

The author of the idea below is Patricia Merz, this is her design and her construction. She kindly provided it for our viewing. Patricia believes that many children, teenagers, and students would like to get such a design completely cheap.

Most cheap way- This make a tablet stand with your own hands!

Tools you will need:

A stationery knife (also called a utility knife or a construction knife),
A ruler approximately 40cm long (you can use any ruler),
An ordinary pencil
Scissors
Screwdriver (or drill).

Materials you will need:

A piece of cardboard measuring 63.5 x 33cm,
Glue for paper or wood,
Adhesive film, color and pattern – your choice!

In the rectangle you need to draw three massive parts, as shown in the sketch, the design uses a material that is easy to find and process, this is three-layer cardboard. If you cannot find three-layer cardboard, use a prefabricated piece and stack each missing layer on top of each other. In this way, the required strength of the product will be achieved.

You can glue the parts together with a suitable glue, for example, PVA or Liquid Nails; they can always be found in a hardware store.

General process: Cut and glue the parts of the tablet stand

The general process is simple - cut a rectangle to size, press a groove on the fold lines, coat it with glue and fold the structure into a triangle. The edges of the acute triangle must be secured to each other. To do this, wedge-shaped “dowels” are made from strips of cardboard and placed in the holes made on the opposite side, using glue.

The lip at the bottom of the stand is required; it prevents the gadget from sliding down. For structural strength, it is advisable to attach the side in the same way as the back of the triangle. After you have glued and dried the structure, treat it with sandpaper and glue the “weak spots” if necessary.

Final stage: Pasting the tablet stand

The next stage is to cover the structure with film. Cut a piece so that there is enough for the edges and folds. In places of bends where it is difficult to glue the film, make cuts and wrap. Glue the film gradually, removing the protective layer and ironing from one edge to the other to release air bubbles.

I was watching a movie on my iPad one day, and suddenly I got tired of putting whatever I could under the tablet. There are also stands. But the stand in the store is miles and money away, but you need it right now and for free.

There are sheets of cardboard and glue.
Task: quickly, easily and cheaply make a stand for a tablet.

What is required from the stand: stability, ease of installation and removal of the tablet, the ability to install at different angles so that it does not break.

Angles. At a minimum, you need a slightly tilted position for individual use, and a nearly vertical position for multiple viewers to see.

What types of stands are there?

I haven’t found a suitable prototype for making it myself. Not suitable: complexity, dependence on material and technology, low reliability of moving parts.

There should be no moving parts, but there should be different installation angles. The stand should be made of a simple material (cardboard, in this case), but reliable and stable.

Solution.
One-piece design with three fixed angles. Triangular section.

Distribute the corners of the triangle for three installation options.

The sum of the angles of a triangle is 180 degrees, the sum of the angles of deviation of the front face from the vertical is 90 degrees. The tablet can be placed at angles of 15, 30 and 45 degrees from the vertical, turning the stand over to the desired side.