We decided to do our own repairs. washing machine? Then you should know the basic subtleties of disassembling it. Otherwise, you simply will not be able to get to the necessary parts, let alone replace them yourself. First, figure out how to remove the top cover of the washing machine, and we will be happy to help you with this.

Step-by-step instruction

First of all, it is necessary to prepare the LG washing machine for dismantling the top cover. To do this, you need to disconnect the “home assistant” from the power supply, turn off the water supply, and disconnect the drain and inlet hoses. Next, you need to move the machine to the middle of the room to make it easier to work with. Now you can remove the top cover.

The LG machine is very heavy, so you need to get someone's help.

1. Walk around the LG washing machine.
2. At the back, right under the protrusion of the top cover, not far from the upper right and left corners of the machine body, there are 2 screws. They need to be unscrewed as they hold the lid in place.
3. After removing the screws, grab the cover with both hands.
4. With considerable effort, pull the lid towards you until it moves a couple of centimeters.
5. Next, simply lift the lid up and move it to the side.

That's all, the cover is dismantled. In this way you can remove the cover on all modern washing machines LG. If the machine lid does not lift or move to the side, it means it is jammed. Don't try to pry it with a screwdriver, rather move it back and forth. You can also gently tap it with a mallet and then try to remove it again. Be patient and everything will work out.

Why is this necessary?

We told you how to remove the cover from an LG washing machine, but what exactly is this for? What parts can a novice master get to if the upper part of the machine body is dismantled?

First of all, you can get to the fill valve of the LG washing machine. If there are problems with the water supply, underfilling or overfilling occurs, first of all you should check the fill valve, and it is located on top in the corner of the housing near the back wall. A novice master can ring the fill valve coil, check the wiring, pipes and even the mechanism. You can also completely replace the faulty part, and all this can be done only by removing the cover, without further disassembling the SM.

Is the powder difficult to wash off? This means you need to check the water supply to the powder receptacle of the LG washing machine, and to do this, you again need to open the top cover. Through top part housing, we get full access to the required pipe, we can remove it and clean it, and also replace it if necessary.

Immediately under the top cover of the machine you can find and. This element should be checked if the machine drains water at the wrong time or refuses to drain it, giving an OE error. Replacing a non-working water level sensor is as easy as shelling pears if you get to it from above: unscrew the mount, remove the power wires, and behold, you have a broken pressure switch in your hands.

By removing the cover of the LG washer, you can also get to the top counterweight. Of course, counterweights break very rarely, but sometimes this happens and, again, you cannot do without dismantling the top cover. You can even remove the tank along with the drum through the upper part of the housing. True, in order to carry out such an operation, you will still have to remove the panel, the front wall and unscrew the technological hatch in the rear of the machine, but the disassembly process, undoubtedly, begins with the cover.

By removing the cover of the LG CM you can even get to surge protector, if suddenly there are problems with the power supply of the machine.

So, removing the cover from the LG washing machine is a fundamental principle, without knowledge of which it is impossible to carry out do-it-yourself repair. Once you take this “first step,” you will subsequently learn everything else. There would be a desire!

How to open the phone cover?

Each of us sooner or later faces the need to change the battery in mobile phone or for one reason or another, to get to its “insides” in order to carry out any manipulations. In most cases, this will be a completely trivial task, since many phones are equipped with removable back panels, which just need to be pryed correctly and the cover will be removed without any problems.

Recently, manufacturers are increasingly starting to produce phones whose back covers may be difficult to remove or may not be removed at all, like a seamless cover on a monolithic phone. Without tools, for example, remove back cover You won't be able to get an iPhone. Let's take a step-by-step look at how to remove the back panel using this smartphone as an example.

Removing the cover

For this we need a small Phillips and flat head screwdriver.

1. Turning off the iPhone is a mandatory step. To avoid damage, you must make sure that the device is completely turned off, and not just the screen has gone dark.
2. We take out the SIM card - this will help prevent it from being damaged when removing the back cover. In the article you will learn what to do to avoid damaging it when removing it.
3. Make sure there is no static electricity on you. To do this, just touch any bare metal.
4. Remove old stickers from screws. There are two small screws on the bottom of the phone that must be removed before you can open the phone. They are located on both sides of the connector.
5. Open the back cover. Here we need a thin screwdriver, which, after the screws are unscrewed, must be carefully inserted between the body and rear panel. Alternatively, you can use a suction cup to remove the back panel.
6. Disconnect the cable. There is a cable attached to the back cover of the iPhone that goes to the motherboard of the device; it also needs to be disconnected.

Now you know how to open the phone cover and what you need to do it. The candy bar phone is disassembled according to the same scheme.

LG G2 disassembly

A complete guide to disassembling the LG G2 phone, with which you can simply disassemble your own phone to replace the monitor or other component that has failed.

Rear lid The phone fits quite tightly to the body; to remove it, take a sharp knife to disconnect one clip.

Now take a plastic tool and, carefully moving along the entire perimeter of the case, disconnect all the clips that hold the back cover.

Locate and remove the five screws that secure the microphone housing to the phone body.

Next, locate and remove the seven screws that secure the plastic protective lid boards to the phone body.

Find two connectors marked in the photo with numbers 1,2 and disconnect them with curved tweezers, then disconnect ten more connectors of the cables shown in the photo.

Now you need take off front camera using curved tweezers.

Small logic boards on both sides and a volume button, secured by a small amount of glue, use the flat end of the spudger tool to lift them up. Before doing this, you can use a hair dryer to warm up the glue.

Now you need to remove the battery from the phone. Using the flat end of a spudger, carefully lift it up. Since it is secured with a small amount of glue, using a heat gun or hair dryer can help.

Replacement Rechargeable Battery LG G2. Step-by-step instruction

Step-by-step instructions for replacement Rechargeable Battery LG G2. More details on our website: .

LG G2 (D802) disassembly and replacement of display, link in description!!!

A small board and speaker housing are fixed at the bottom of the phone with glue. Use a little heat and the flat side of your spudger tool to gently lift them up and out.

Remove the motherboard from the case by carefully pulling it up.

We remove the touch sensor; to do this, disconnect the connector and remove the sensor itself with tweezers.

Now, using the thin tip of curved tweezers, remove the rear camera. She keeps it small amount of glue, so using a heat gun or hair dryer can be helpful.

The earpiece should already be free to remove. Use a small amount of heat from a hair dryer to warm up the adhesive holding the cable in place, then use the fine tip of a pair of curved tweezers to pull the speaker out of the housing.

The display assembly (LCD and touch screen) is connected together and fixed to the case big amount glue. You will need heat and a lot of patience to separate the display from the case. This procedure is only recommended on an LG G2 phone with a damaged display that requires replacement. Use a heat gun or hair dryer to heat the adhesive holding the display (LCD and touch screen) with the front of the body. The heat will weaken the glue holding the pieces together.

To separate the display from the front of the case, use one of the screwdrivers to press the display through the hole in the front camera.

You can now use a plastic tool or spudger to separate the display from the front of the case.

Disassembling the LG G2 is a labor-intensive task that requires care and attention, so do not proceed with disassembly if you are not confident in your abilities!

Complete instructions for disassembling the LG G2 smartphone, with which you can easily disassemble your phone to replace the display or other component that has failed.

The back cover of the phone fits quite tightly to the body; to remove it, take a sharp knife to disconnect one clip.

Now take a plastic tool and carefully move around the entire perimeter of the case to remove all the clips that hold the back cover.

Locate and remove the five screws that secure the microphone housing to the phone body.

Next, locate and remove the seven screws that secure the plastic protective board cover to the phone body.

Find two connectors marked in the photo with numbers 1,2 and disconnect them with curved tweezers, then disconnect ten more connectors of the cables shown in the photo.

Now you need to remove the front camera using curved tweezers.

The small logic boards on both sides and the volume button are secured with a small amount of glue, use the flat end of a spudger tool to pry them up. Before doing this, you can use a hair dryer to warm up the glue.

Now you need to extract battery from the phone. Using the flat end of a spudger, carefully lift it up. Since it is secured with a small amount of glue, using a heat gun or hair dryer can help.

A small board and speaker housing are fixed at the bottom of the phone with glue. Use a little heat and the flat side of your spudger tool to gently lift them up and out.

Remove from the body motherboard, carefully pulling it up.

We remove the touch sensor; to do this, disconnect the connector and remove the sensor itself with tweezers.

Now, using the thin tip of curved tweezers, remove the rear camera. It is held in place with a small amount of glue, so using a heat gun or hair dryer can be helpful.

The earpiece should already be free to remove. Use a small amount of heat from a hair dryer to warm up the adhesive holding the cable in place, then use the fine tip of a pair of curved tweezers to pull the speaker out of the housing.

The display assembly (LCD and touch screen) are connected together and secured to the body with a large amount of adhesive. You will need heat and a lot of patience to separate the display from the case. This procedure is only recommended on an LG G2 phone with a damaged display that requires replacement. Use a heat gun or hair dryer to heat the adhesive holding the display (LCD and touch screen) to the front of the case. The heat will weaken the glue holding the pieces together.

To separate the display from the front of the case, use one of the screwdrivers to press the display through the hole in the front camera.

You can now use a plastic tool or spudger to separate the display from the front of the case.

Disassembling the LG G2 is a labor-intensive task that requires care and attention, so do not proceed with disassembly if you are not confident in your abilities!

If our instructions helped you: "Disassembling the LG G2", support our site - share the link with your friends:
Dear users, if you have any questions about the instructions: “Disassembling LG G2”, ask a question in the comments or via the link!
We will try to answer you in the shortest possible time and give a detailed answer to your problem!